Cipherlab |
Post Reply | Page 12> |
Author | |
peach
Admin Group THE BOSS Joined: 01-Jan-2006 Status: Offline Points: 1295 |
Post Options
Thanks(0)
Posted: 06-Aug-2008 at 04:23 |
pda cipherlab
As default the barcode scanner is not activeated
Two computers showed at the base of screen but with cross
(NOte if two computers are not at the bottom of the screen there will be a round orange P symbol. Click it and then select WiFi Power on)
There are arrows on the task bar to the left and right if more in the task bar than can be displayed.
There is an antenna signal giving signal strength at base 94reader icon on the screen is the barcode program Internet explorer is on the desktop Spare battery in back of stand is on charge On screen left to right at base
DblClk ean13/upc
ean 13 / upc/a add on 2
add on 5
isbn conversion
issn conversion tx ean13 chk digit tick
Convert upc-ean13
tx upca chk digit tick
tx system number tick
enable gtin for ean13
when screen closes barcode icon should be at base left of the information icon mentioned above.
to have the screen go for more than 15seconds: Check Power properties scheem:
standard settings.. switch state to user idle after 1 minute
system to idle after 3 minutes
system state suspend after 5min
Connectivity:
Dble click the two computers at the base
SETUP STOCKPDA AS USUAL. THE TOP SIDE BOTTONS SEEM TO BE ENTER BUTTONS, THE SIDE BUTTONS UNDER THOSE ARE FOR THE SCANNER. INITIALLY MY SCANNER DID NOT WORK SO I WENT BACK INTO THE SCANNER OPTIONS AND SET KEYBOARD EMULATION AGAIN AND OK. IT STARTED WORKING PROPERLY AFTER THAT. Edited by peach - 13-Sep-2012 at 04:32 |
|
Pouya
PEACH STAFF THE POY Joined: 21-Dec-2006 Status: Offline Points: 455 |
Post Options
Thanks(0)
|
Also - by factory default, the 9400 is set to search for multiple Access Points. This makes the connection to the primary access point weaker reducing the usable distance.
To turn off the multiple Access Point:
1. Double click on the 2 Blue Computers at the base
2. Goto the "WiFi Configuration" Tab (Last one)
3. Untick the "Adaptive Connection" Checkbox.
4. Ok and Close. Edited by peach - 07-Oct-2008 at 12:37 |
|
Guests
Guest |
Post Options
Thanks(0)
|
when recieving an error on the pda saying that the progrqam is not compatible with microsoft. go to the website:
http://www.peachsoftware.com.au/pda.htm - If you have Model Cipher Lab 9400 then you need Ver5.0 - all other PDa's use ver 4.2 - download the file to the PDA and run it. - once you run it, it will want to install in the \Windows folder. - just click on OK and let it complete. - then the stock PDa will work. Edited by peach - 04-May-2009 at 02:20 |
|
peach
Admin Group THE BOSS Joined: 01-Jan-2006 Status: Offline Points: 1295 |
Post Options
Thanks(0)
|
When the unit is shipped somtimes the IP is set as static. neeed to change to get ip from network......Start - Control Panel - Network Connection Settings - WlAn - Get ip from network.
|
|
peach
Admin Group THE BOSS Joined: 01-Jan-2006 Status: Offline Points: 1295 |
Post Options
Thanks(0)
|
easy way to browse to a web site is to start keyboard and then start wordpad from programs. type the adres and it will creat the link and then click it. This will open the address in IE.
When applications suchas wordpad and IE are open you cant get to the keyboard. So start the keyboard first
|
|
peach
Admin Group THE BOSS Joined: 01-Jan-2006 Status: Offline Points: 1295 |
Post Options
Thanks(0)
|
Make sure when you enter the area in the case of a consignment system the area & Case is correct. The transaction trail in a consignment system is not very good, needs work.
As far as the InStkQty is concerned after a gen stats its ok.
|
|
peach
Admin Group THE BOSS Joined: 01-Jan-2006 Status: Offline Points: 1295 |
Post Options
Thanks(0)
|
Barcodes with zero in front.
some barcodes starting with a zero dont work. try putting another 0 in front of the barcdoe in Peach. You cn test this by clearing the barcode in a certain part then find it by the part number on the pda, scan the barcode into it and update. Now look at peach and see what number it has entered. Test that the scanner can now scan the part successfully and your done.
|
|
Pouya
PEACH STAFF THE POY Joined: 21-Dec-2006 Status: Offline Points: 455 |
Post Options
Thanks(0)
|
WHERE IS THE RESET BUTTON
ON FRONT OF PDA
1CM LEFT OF THE ON/OFF BUTTON
(Only an indent, not a hole right through, so use a paper clip)
|
|
peach
Admin Group THE BOSS Joined: 01-Jan-2006 Status: Offline Points: 1295 |
Post Options
Thanks(0)
|
cipherlab service tech is John Zhang at JRC 96213377
|
|
Guests
Guest |
Post Options
Thanks(0)
|
WIFI CONNECTION - Follow this in the specific order set if you are having troubles connecting to the internet: 1. Delete any existing profiles in your wifi settings. TURN YOUR WIFI OFF - Click the "signal" icon at the bottom of screen and power off wifi. 2. Edit the Wifi adapter to assign or auto assign an IP Address. To get there click Start > settings > network & dial-up connections. For a specific IP Address you will need an 'unassigned' IP address e.g. 10.0.0.20 > the 'Subnet Mask' will be 250.0.0.0 and the gateway will be the "Servers" internal IP Address which can be found on the server machine by typing in "ipconfig /all" without the quotes in command prompt. (Command prompt is found by Start > Run > type "cmd") After you have done this goto the "Name Servers" Tab and the 'Primary DNS' should read the same as your Gateway or internal ip. When this is done click OK (top right hand corner) and go back to wifi settings (click 2 computers at bottom of desktop) and Goto the 'wireless information' tab again and double click on the Network you wish to join > select the appropriate settings for your type of Wireless > click ok and try to connect again. |
|
Post Reply | Page 12> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |